今天给各位分享钢筋工安全技术交底.doc的知识，其中也会对钢筋工安全技术交底.doc进行解释，如果能碰巧解决你现在面临的问题，别忘了关注本站，现在开始吧！
钢筋工安全技术交底.doc的介绍就聊到这里吧，感谢你花时间阅读本站内容，更多关于钢筋工安全技术交底.doc、钢筋工安全技术交底.doc的信息别忘了在本站进行查找喔。
本文导读目录：
3、安全技术交底汇总146例，你需要的基本都在里面，覆盖面广
安全技术交底表表AQ-C11-1编号0005工程名称地铁14号线工程 东管头站施工单位北京城建集团有限责任公司北京地铁14号线工程土建施工05合同段项目经理部交底部位钢筋笼制作工种钢筋工安全技术交底内容一般要求1. 作业人员必须经过安全技术培训，掌握本工种安全生产知识技能。2. 新工人或转岗工人必须经入场或转岗培训，考核合格后方可上岗，实习期间必须在有经验的工人带领下进行作业。3. 作业前必须检查工具、设备、现场环境等，确认安全后方可作业。4. 严禁在高压线下堆土、堆料、支搭临时设施和进行机械吊装作业。5. 非机械操作工作和非电厂严禁进行需专业人员操作的机械、电气作业。6. 特种作业人员必须经过安全技术培训，取得主管部门颁发的资质证后方可持证上岗。7. 作业前必须听取安全技术交底，掌握交底内容。作业中必须执行安全技术交底。没有安全技术交底严禁作业。 8. 作业时必须按规定使用防护用品。进入施工现场的人员必须戴安全帽、严禁赤脚，严禁穿拖鞋。针对性交底一、手工加工与绑扎1. 作业前必须检查工作环境、照明设施等，并试运行符合安全要求后方可作业。2. 切断长料时，应设专人扶稳钢筋，操作时动作应一致。钢筋短头应使用钢管套夹具夹住。钢筋短于30cm 时，应使用钢管套夹具，严禁手扶。切断合金钢和直径10mm 以上圆钢时应采用机械。3. 工作完毕后，应用工具将铁屑、钢筋头清除，严禁用手擦抹或用嘴吹。切好的钢材、半成品必须按规格码放整齐。4. 抬运钢筋人员应协调配合，互相呼应。5. 电动机械的电闸箱必须按照规定安装漏电保护器，并应灵敏有效。6. 人工弯曲钢筋时，应放平扳手，用力不得过猛。7. 展开盘条钢筋时，应卡牢端头。切断前应压稳，防止回弹伤人。8. 抬运、吊装钢筋骨架时，必须服从指挥。交底人姓名职务交底时间2011.10.11接受交底人签名注：1、项目对操作人员进行安全技术交底时填写此表；2、 签名出不够时，应将签到表附后。安全技术交底表表AQ-C11-1编号0005工程名称地铁14号线工程 东管头站施工单位北京城建集团有限责任公司北京地铁14号线工程土建施工05合同段项目经理部交底部位2号竖井钢筋笼制作工种钢筋工安全技术交底内容针对性交底二、钢筋加工机械操作人员1. 调直机操作人员安全操作要求：l）调直机安装必须平稳，料架料槽应平直，对准导向筒、调直筒和下刀切孔的中心线。电机必须设接零保护。2） 使用调直机作业时，机械上不得堆放物料、工具等，避免震动落入机体。送钢筋时，手与轧辊应保持安全距离。机器运转中不得调整轧辊。严禁戴手套作业。3）作业中机械周围不得有无关人员，严禁跨越牵引钢丝绳和正在调直的钢筋。钢筋调直到末端时，作业人员必须与钢筋保持安全距离。料盘中钢筋将要用完时，应采取措施防止端头弹出。4）调直短于2m 或直径大于9mm 的钢筋时，必须低速运行。5）喂料前应将不直的钢筋头切去，导向筒前应装一根lm 长的钢管，钢筋必须先通过钢管再送人调直机前端的导孔内，当钢筋穿人后，手与压棍必须保持安全距离。6）圆盘钢筋放入放圈架上要平稳，乱丝或钢筋脱架时，必须停机处理。已经调直的钢筋，必须按规格、根数分成小捆，散乱钢筋应随时清理堆放整齐。2. 切断机操作人员安全操作要求：1）操作前必须检查切断机刀口，确定安装正确，刀片无裂纹，刀架螺栓紧固，防护罩牢靠，然后拨动皮带轮检查齿轮间隙，调整刀刃间隙，空运转正常后再进行操作。2）使用切断机作业时应摆直、紧握钢筋，应在活动切刀向后退时送料人刀口，并在固定切刀一侧压住钢筋。严禁在切刀向前运动时送料。严禁两手同时在切刀两侧握住钢筋俯身送料。3）钢筋切断应在调直后进行，多根钢筋一次切断时总截面积应在规定的范围内。4）切长料时应设置送料工作台，并设专人扶稳钢筋，操作时动作应一致。手握端的钢筋长度不得短于40cm ，手与切口间距不得小于15cm 。切断小于40cm 长的钢筋时，应用钢导管或钳子夹牢钢筋。严禁直接用手送料。 5）作业中严禁用手清除铁屑、断头等杂物。机械运转中严禁进行检修、加油、更换部件。交底人姓名职务交底时间2011.10.11接受交底人签名注：1、项目对操作人员进行安全技术交底时填写此表；2、签名出不够时，应将签到表附后。安全技术交底表表AQ-C11-1编号0005工程名称地铁14号线工程 东管头站施工单位北京城建集团有限责任公司北京地铁14号线工程土建施工05合同段项目经理部交底部位2号竖井钢筋笼制作工种钢筋工安全技术交底内容针对性交底二、钢筋加工机械操作人员3. 调直机操作人员安全操作要求：l）调直机安装必须平稳，料架料槽应平直，对准导向筒、调直筒和下刀切孔的中心线。电机必须设接零保护。3） 使用调直机作业时，机械上不得堆放物料、工具等，避免震动落入机体。送钢筋时，手与轧辊应保持安全距离。机器运转中不得调整轧辊。严禁戴手套作业。3）作业中机械周围不得有无关人员，严禁跨越牵引钢丝绳和正在调直的钢筋。钢筋调直到末端时，作业人员必须与钢筋保持安全距离。料盘中钢筋将要用完时，应采取措施防止端头弹出。4）调直短于2m 或直径大于9mm 的钢筋时，必须低速运行。5）喂料前应将不直的钢筋头切去，导向筒前应装一根lm 长的钢管，钢筋必须先通过钢管再送人调直机前端的导孔内，当钢筋穿人后，手与压棍必须保持安全距离。6）圆盘钢筋放入放圈架上要平稳，乱丝或钢筋脱架时，必须停机处理。已经调直的钢筋，必须按规格、根数分成小捆，散乱钢筋应随时清理堆放整齐。4. 切断机操作人员安全操作要求：1）操作前必须检查切断机刀口，确定安装正确，刀片无裂纹，刀架螺栓紧固，防护罩牢靠，然后拨动皮带轮检查齿轮间隙，调整刀刃间隙，空运转正常后再进行操作。2）使用切断机作业时应摆直、紧握钢筋，应在活动切刀向后退时送料人刀口，并在固定切刀一侧压住钢筋。严禁在切刀向前运动时送料。严禁两手同时在切刀两侧握住钢筋俯身送料。3）钢筋切断应在调直后进行，多根钢筋一次切断时总截面积应在规定的范围内。4）切长料时应设置送料工作台，并设专人扶稳钢筋，操作时动作应一致。手握端的钢筋长度不得短于40cm ，手与切口间距不得小于15cm 。切断小于40cm 长的钢筋时， 1、钢筋工安全技术交底内容钢筋工安全技术交底内容PAGE2钢筋工安全技术交底内容钢筋工安全技术交底内容一、安全常识1、进入施工现场必须戴好安全帽，高空作业系好安全带，正确使用个人劳动防护用具，操作人员必须身体健康。2、施工现场作业人员严禁酒后上岗，疲劳作业、带病作业。3、进入施工现场必须遵守施工现场安全管理制度，严禁违章指挥，违章作业，施工人员对违章指挥有拒绝权；做到四不伤害：不伤害自己，不伤害他人，不被他人伤害，保护他人不受伤害。 二、钢筋制作钢材半成品等，应按规格，品种分别码放整齐达到一头齐，每种都有标牌。制作场要平整，钢筋加工机械按工序传递安装牢固，工作台要稳固，防护罩齐全。拉直钢筋，安全防 2、护是大事，卡头要牢，地锚要坚实。在拉筋区域2米内禁止有行人。多人合运钢筋，起落转停动作要一致，人工上下传递不得在一道垂直线上，防止散落伤人。钢筋绑扎：在高空、深坑绑扎钢筋和安装半成品料时，必须搭设工作段后，上人要走坡道。绑扎立柱、墙体钢筋时不得在绑好的钢筋骨架上攀登上下，在4米以上柱墙体要搭设临时作业台，临时支撑，防止倾倒伤人。绑扎基础钢筋时应按施工设计规定摆放钢筋支撑不得任意减少。施工马凳及时放置，不得踩踏钢筋造成移位。施工时注意脚下安全。绑扎外墙边柱要加强外挂架临边防护。钢筋骨架起落时，下方不准行走站人。钢筋机械：切断机待运转正常后方可断料手与刀口距离不得少于15CM。切长料时，操作配合好动作一致，切短料时，不得用手垂直接送取料。切断机旁要设料台，严禁在运转中清理刀口附近的料头。弯曲机要紧贴档板，注意回转方向，弯长料要有专人配合，防止碰伤他人。对焊机，要设在干燥、平整、接地可靠、线绝缘良好的场地上。作业时要戴好个人防护用品，站在操作台上，工作棚要防火，周 1、钢筋作业安全技术交底······························································· 7 2、砼施工作业安全技术交底··························································· 11 3、木工支模作业安全技术交底······················································· 13 4、脚手架搭设、拆除作业安全技术交底········································ 17 5、土方开挖作业安全技术交底······················································· 18 6、马道、护头棚安全技术交底······················································· 19 7、卸料平台搭设作业安全技术交底················································ 20 8、防水作业安全技术交底······························································· 22 9、库房防水材料管理安全技术交底················································ 23 10、调漆作业安全技术交底····························································· 24 11、喷漆作业安全技术交底····························································· 25 12、屋面防水作业安全技术交底····················································· 26 13、油漆作业安全技术交底····························································· 27 14、大模板施工作业安全技术交底················································· 30 15、钢结构施工作业安全技术交底················································· 33 16、清理、清运作业安全技术交底················································· 34 17、钢管、料具码放作业安全技术交底·········································· 35 18、安全网支搭作业安全技术交底················································· 36 19、抹灰作业安全技术交底····························································· 37 20、吊顶作业安全技术交底····························································· 40 21、玻璃安装作业安全技术交底····················································· 41 22、大理石干挂作业安全技术交底················································· 42 23、玻璃幕墙安装作业安全技术交底·············································· 43 24、外墙抹灰作业安全技术交底····················································· 44 25、外墙涂料作业安全技术交底····················································· 45 26、外爬架作业安全技术交底························································· 46 27、外挂架作业安全技术交底························································· 47 28、挑脚手架作业安全技术交底····················································· 50 29、拆除工程作业安全技术交底····················································· 52 30、回填土作业安全技术交底························································· 53 31、内外墙面砖、地砖粘贴作业安全技术交底······························ 55 32、井字架搭拆作业安全技术交底················································· 56 33、管道施工、水暖工作业安全技术交底······································ 63 34、外电线路防护架搭拆作业安全技术交底·································· 65 35、电焊作业安全技术交底····························································· 67 36、现场临时用电作业安全技术交底·············································· 69 37、冬季施工用电作业安全技术交底·············································· 70 38、一级(A)配电柜安装作业安全技术交底····································· 72 39、二级(B)配电箱安装作业安全技术交底····································· 4 40、三级(C)配电线安装作业安全技术交底····································· 76 41、塔吊上镝灯安装作业安全技术交底·········································· 77 42、木工设备照明安装作业安全技术交底······································ 78 44、砼振捣器接线使用安全技术交底·············································· 79 45、低变照明安装作业安全技术交底·············································· 80 46、办公区、生活区食堂用电设备安装作业安全技术交底··········· 81 47、雨季施工用电作业安全技术交底·············································· 83 48、打夯机使用作业安全技术交底················································· 85 49、消防水泵安装作业安全技术交底·············································· 86 50、气焊、气割作业安全技术交底················································· 87 51、电焊机的安装搬运和使用作业安全技术交底··························· 89 52、塔吊作业（含群塔作业）安全技术交底·································· 91 53、外用电梯安装使用作业安全技术交底······································ 93 54、电动吊篮的安装、调试、使用安全技术交底··························· 94 55、无齿切割机切割作业安全技术交底·········································· 105 56、圆盘锯使用安全技术交底························································· 107 57、车、机床加工操作作业安全技术交底······································ 108 58、塔吊、外用电梯的拆立作业安全技术交底······························ 109 59、汽车吊吊装作业安全技术交底················································· 111 60、信号指挥作业安全技术交底····················································· 112 61、机具切割作业安全技术交底····················································· 113 62、通风及设备安装作业安全技术交底·········································· 114 63、路基工程作业安全技术交底····················································· 116 64、路面工程作业安全技术交底····················································· 120 65、旧路面凿除作业安全技术交底················································· 122 66、推土机、安装机作业安全技术交底·········································· 123 67、炊事作业安全技术交底····························································· 126 68、临时设施施工作业安全技术交底·············································· 127 69、库房保管安全技术交底····························································· 129 70、铁件加工作业安全技术交底····················································· 130 71、暗挖作业安全技术交底····························································· 132 72、物料装卸作业安全技术交底····················································· 137 73、绿化作业安全技术交底····························································· 138 74、砼地泵（含布料杆）安全技术交底·········································· 139 75、塔机操作安全技术交底····························································· 140 76、搅拌作业安全技术交底····························································· 141 77、放线测量作业安全技术交底····················································· 142 78、挂勾工操作安全技术交底························································· 143 79、场内运输作业安全技术交底····················································· 144 80、木工（模板工）施工安全技术交底·········································· 145 81、木工机械安全使用交底·························································· 148 82、壮工施工安全技术交底····························································· 151 83、钢筋工施工安全技术交底························································· 156 84、预应力钢筋张拉工安全技术交底·············································· 160 85、焊工施工安全技术交底····························································· 161 86、混凝土工施工安全技术交底····················································· 167 87、架子工施工安全技术交底························································· 169 88、起重工（挂钩工、信号工）施工安全技术交底······················· 177 89、瓦工、抹灰工施工安全技术交底·············································· 181 90、防水工施工安全技术交底························································· 183 91、油漆工、玻璃工施工安全技术交底·········································· 184 92、测量工施工安全技术交底························································· 185 93、动力机械操作工操作安全技术交底·········································· 186 94、铲土运输机械和基础施工机械操作人员安全技术交底··········· 188 95、混凝土机械操作工安全技术交底·············································· 189 96、起重运输机械操作工操作安全技术交底·································· 195 97、内燃机操作安全技术交底························································· 202 98、发电机操作安全技术交底························································· 203 99、空气压缩机操作安全技术交底················································· 204 100、10KV以下配电装置安全技术交底········································· 205 101、手持电动工具操作安全技术交底··········································· 207 102、履带式起重机操作安全技术交底··········································· 209 103、汽车、轮胎式起重机操作安全技术交底································ 211 104、卷扬机操作安全技术交底······················································· 213 105、土石方机械操作安全技术交底··············································· 214 106、单斗挖掘机械操作安全技术交底··········································· 215 107、挖掘装载机操作安全技术交底··············································· 217 108、推土机操作安全技术交底······················································· 218 109、轮胎式装载机操作安全技术交底··········································· 220 110、蛙式夯实机操作安全技术交底··············································· 222 111、振动冲击夯操作操作安全技术交底········································ 223 112、自卸汽车安全技术交底··························································· 224 113、叉车安全技术交底·································································· 226 114、桩工机械操作安全技术交底··················································· 227 115、履带式打桩机（三支点式）操作安全技术交底····················· 228 116、混凝土搅拌机操作安全技术交底··········································· 229 117、混凝土搅拌输送车操作安全技术交底···································· 231 118、插入式振动器操作安全技术交底··········································· 234 119、电焊工具和使用安全技术交底··············································· 235 120、气焊与气割器具使用安全技术交底········································ 237 121、排水和降低地下水位安全技术交底········································ 238 122、基坑支护施工安全技术交底··················································· 241 123、桩基工程施工安全技术交底··················································· 249 124、木模板（含木夹板）安装、拆除安全技术交底····················· 253 125、定型组合钢模板安装与拆除安全技术交底···························· 254 126、大模板安装与拆除安全技术交底··········································· 255 127、滑动模板安装与拆除安全技术交底········································ 256 128、爬模安装与拆除安全技术交底··············································· 257 129、屋面工程施工安全技术交底··················································· 258 130、脚手架工程施工安全技术交底··············································· 261 131、扣件式钢筋脚手架搭设与拆除安全要求································ 264 132、门式钢管脚手架搭拆安全技术交底········································ 268 133、碗扣式钢管脚手架搭拆安全技术交底···································· 272 134、附墙升降脚手架安全技术交底··············································· 274 135、抹灰、饰面施工安全技术交底··············································· 279 136、油漆、喷涂、刷浆施工安全技术交底···································· 282 137、玻璃安装安全要求·································································· 285 138、铝合金玻璃幕墙安装的安全技术交底···································· 286 139、烟囱工程施工安全技术交底··················································· 287 140、高处作业安全技术交底··························································· 290 141、临边作业安全技术交底··························································· 291 142、洞口作业安全技术交底··························································· 292 143、攀登作业安全技术交底··························································· 294 144、悬空作业安全技术交底··························································· 295 145、操作平台安全技术交底··························································· 297 146、现场临时用电接地与防雷安全技术交底································ 298钢筋工安全技术交底.doc的介绍就聊到这里吧，感谢你花时间阅读本站内容，更多关于钢筋工安全技术交底.doc、钢筋工安全技术交底.doc的信息别忘了在本站进行查找喔。
未经允许不得转载！ 作者:谁是谁的谁，转载或复制请以超链接形式并注明出处。
原文地址：http://www.kpfe.org/post/11305.html发布于：2026-01-03
